Can I Burn the Tree That Was Cut Down Yesterday?

Technically, you can burn off a tree that has been cut yesterday, but its effectiveness relies considerably on whether or not the tree was already dead. Burning a newly cut live tree wood, called “green wood,” is not the best use of the resource or protected in a house. Green wood’s high moisture content makes the wood hard to burn. The moisture also leads to excessive smoke, causing green wood to be a poor choice for indoor furnaces or wood stoves.

Understanding Moisture’s Effects

Using green wood can negatively affect wood consumption by around 25 percent. More than one-half the weight of green wood may be from water. A lot of energy is needed to burn off all that moisture — energy that could move toward supplying heat and a sustained flame. The ideal water percentage in wood for burning is below 20 percent by weight.

Seasoning Wood

The minimum quantity of time to dry, or season, green wood for maximum output is about six months. Split the wood into manageable pieces, and stack the pieces over the ground. Put pallets or a comparable base underneath the woodpile to maximize its ventilation, and stack the wood so the pile comprises some spaces for air to leak throughout it. Place a tarp or comparable weather-resistant cover over only the woodpile’s top. The tarp prevents water from getting into and pooling within the woodpile, a situation that could result in rot.

Recognizing Dry Wood

When wood is dry enough to burn indoors, its characteristics have changed. Dry wood is lighter in color and weight than green wood from the same type of tree. Also, its bark becomes loose and could be peeled easily. Cracks may seem, particularly toward the ends of the logs. The sappy, woody aroma fades. Dry wood creates a distinctive sound — a hollow crack — when hit. So strike two pieces of the wood together, and listen for that sound.

Burning Green Wood

When you have to burn green wood, then do this outdoors where lots of ventilation is available to counteract the smoke. Before lighting the fireplace, split the wood into very little pieces, and blend those pieces with dry kindling. Place the mixture inside a suitably sized burn container or passion pit, stacking the tiny pieces so that air may flow around the whole pile that will be burned. The higher the stack’s atmosphere consumption isalso the hotter the flame will burn and the faster the wood’s water will dissipate. Stand clear of the wood since it burns, and expect to hear lots of popping and observe its results, clear indicators that the water is burning.

See related

The Way to Employ Talstar Granules in the Yard

Talstar is a new bifenthrin insecticide sold in granular form for control of ground-dwelling insect pests. It’s lethal to over 20 different pest species which lawns and other landscaped areas around constructions, institutions or houses. It is approved for outdoor recreational playing fields. It’s not authorized to use on crops grown for seed or for food. Nor is it accepted for use on greenhouses, golf courses, sod farms or nurseries. Always avoid skin contact when using this product.

Remove. Put including a shirt and long pants. Place on eye protection, work gloves, a hat and a dust mask. Avoid getting Talstar insecticide in your bare skin. If you receive it on your bare hands, arms or body regions take off contaminated clothing and wash affected areas.

Pour Talstar granules to your yard spreader’s hopper. Apply to your yard at a speed of 100 pounds per acre or 2.3 pounds per 1,000 square feet. On areas such as athletic fields, you may apply double those amounts. Walk at a constant speed, so the edge of every row only overlaps the edge of the row, pushing the spreader When employing a walk-behind spreader. Drive at 3 miles an hour in parallel rows, hardly overlapping the preceding row, When using a spreader mounted on a yard tractor.

Water Talstar by employing 1/4 inch to 1/2 inch of water based on the targeted pest infestation to the floor. Two weeks, if you notice signs of renewed insect activity, wait and apply a Talstar treatment.

Employ additional Talstar to control fire ants (Solenopsis invicta), a significant stinging lawn pest at the Southwestern and Southeastern United States. While air application of Talstar will kill foraging workers, place treatment to kill the queens must be received by every fire ant mound in your yard. Employ 1/2 cup of Talstar granules in and around each mound. Break the very top of every mound up and instantly so the insecticide can dissolve soak the mound with 1 to 2 gallons of water and flow into the mound.

See related

The way to Get Rid of Bad Odor on Feather Pillows

Feather cushions may smell a little even if they’re brand new. Whether they have been used or kept in storage, then the cushions hold in smells from sweat, pet hair, cigarette smoke — you name it. Remove those beautiful scents by providing the cushions a dose of fresh air and a trip through the washing machine.

Remove the pillowcases from the pillows. Set the pillows outdoors on a non-humid day to air them out, flipping or rotating them every hour or two to expose all of the surfaces to new air over a few hours. If you are concerned about their getting dirty, keep them on the porch or on a table beneath a patio umbrella. Fresh air helps eliminate all types of scents from cushions, new and old.

Examine the seams of their cushions to make sure there are not any holes. Search for masks along the seam, which signal a hole. Stitch the seam closed again, if necessary, with a thread and needle.

Set the cushions, two at a time, in the washing machine. Pick a delicate or fragile wash cycle along with cool water. Insert a small amount of a mild laundry detergent — less than half of what you use for a regular load; otherwise, the soap may be tough to rinse from their cushions.

Run an extra rinse cycle following the cushions finish a single wash, and rinse. If your washing machine has an option for an elongated spin cycle, then select it, since this will force a lot of the water from their cushions.

Remove the pillows from the washing machine and fluff them up a little. Independent any clumps you believe, then set the pillows in the dryer.

Pick the lowest heat setting on the dryer and include a few tennis balls into the load to maintain the cushions fluffy. Open the dryer partway through the cycle and then fluff the pillows up before putting them back in the dryer. If the cushions still feel wet after a whole drying cycle, then run them through a different drying cycle.

Remove the cushions from the dryer and texture them to determine if they’re completely dry. If they are still slightly damp, hang them over a clothesline or even sweater-drying rack to air dry, or set them back in the dryer for a partial drying cycle.

Wait an hour or so before using or storing the cushions; this allows enough cooling time following the dryer for you to tell if they really are dry, or still damp. Merely use or store the cushions if they’re completely dry; otherwise, they can develop musty smells.

See related

What's Done to Decrease Soil Erosion on Steep Slopes?

Heavy rain can spell disaster for soil on slopes that are steep, but careful plant management, ground cover plants, mulches and help keep it from being washed off. Erosion creates runoff, which pollutes ground water and creates pools that are soggy at incline bases. Erosion also exposes plant roots, which makes them exposed to drying out. A range of methods reduce soil erosion, depending on skills, the available time and budget.

Planting and Watering

Improved pruning and planting methods reduce soil erosion on steep slopes. Plants should be planted vertically — maybe not at right angles to the slope — and the soil should be piled up round the edge of the planting holes to make wells. These hold it while it sinks to the soil around plant roots and catch water. Other practices include watering plants rarely but deeply to promote their roots to grow down. Plants are anchored by roots and also help keep soil. Frequent, light watering encourages shallow roots, that can be drying outside and exposed to exposure. Drip irrigation systems are the best method for watering plants on slopes that are steep if the budget allows. These don’t wash soil away and provide water at a rate that is continuous.

Controling Soil

Heavy rain washes away bare soil on steep slopes, but soil amendments and mulches reduce soil loss. Soils absorb water fast and keep moisture reducing the quantity lost to erosion. A two – to 3-inch layer of compost, leaf mold, well-rotted manure or other fine organic matter, tilled into the soil surface, helps it remain in place. Some work better than others, although mulches include protection. Cocoa hulls, straw, wood chips and loose mulches wash off from rain, but mulches like amalgamated, vineyard amalgamated and finely shredded redwood mulch knit and resist erosion.

Growing Ground Cover Plants

Ground cover plants protect soil and spread over slopes. Their leaves softens the impact of rain and also their origins absorb it, preventing water from flowing slopes down. Bishop’s hat”Discolor” (Epimedium × versicolor”Discolor”), moss phlox”Millstream Daphne” (Phlox subulata”Millstream Daphne”) and heath aster (Symphyotrichum ericoides) are erosion-resistant ground cover plants. “Discolor” grows well on shady slopes and includes yellow and pink spring blossoms. Hardy in U.S. Department of Agriculture plant hardiness zones 5 through 9,”Discolor” climbs 9 to 12 inches tall and 9 to 18 inches wide. “Millstream Daphne” and heath aster develop best on full-sun slopes. “Millstream Daphne,” that is hardy in USDA zones 3 through 9, bears clear pink spring blossoms, and grows 3 to 6 inches tall and 6 to 12 inches wide. Heath aster bears white, late-summer blossoms and grows 12 to 36 inches tall and 12 to 18 inches wide. This shrubby perennial is hardy in USDA zones 3. Plant ground cover plants flat against slopes.

Building Terraces

For people with good DIY skills or the budget terraces reduce soil erosion on slopes. Terraces are growing areas that look like measures on slopes and hillsides. Terrace walls hold soil in place, and the beds can be used for growing vegetables or ornamental plants. Good DIY skills are all that’s required to construct terraces but call in an expert builder for more ambitious projects. Be careful not to pay exposed tree roots their root systems, In case you choose to construct your own terraces.

See related

Organic Remedy for Bagworms

Bagworms are caterpillars that spin protective sacks and the leaves, twigs and bark of their host plants. The brown, teardrop-shaped bags reach 1- to 2-inches long and generally seem like seedpods or small robes. These voracious eaters can defoliate host plants, causing them to weaken, seem unattractive and even die. Without releasing compounds into the 15, several organic treatments exist to treat bagworm people.

Around Bagworms

Bagworms (Thyridopteryx ephemeraeformis) will feed on about 130 plant species, but their favourite foods will be the junipers (Juniperus spp.) , such as red cedars and Leyland cypress trees, which grow in U.S. Department of Agriculture plant hardiness zones 2 through 9 and zones 6 through 9, respectively. Bagworm men are fuzzy moths using wingspans, but the mature females are flightless, worm-like animals that reach about 1 inch in length and never leave their bags. They set between 500 and 1,000 eggs before perishing inside of the bags. The blackish caterpillars emerge, and the eggs hatch once warm weather arrives at the spring and start feeding on their host plants.

Handpick Bags

You can typically control localized or small bagworm inhabitants by handpicking and ruining the bags, however you must do this no later than early spring to prevent the eggs from hatching. Dip the bags into a pail of soapy water instead of simply letting them drop to the floor. This guarantees that the caterpillars don’t return for their host plants. After you eliminate the sacks, cut the lace bands which attach the bags. This silk can girdle limbs and cause branch dieback in only a few decades, if you don’t.

Bring Natural Enemies

Bagworms have loads including wasps and birds. Bring the predatory beneficial insects by planting daisy and aster family members. Shasta daisies (Leucanthemum X superbum) and Frikart’s asters (Aster x frikartii) both work as attractants while incorporating pops of colour in yards throughout USDA zones 5 through 9. Feeders, Putting birdbaths and birdhouses near trees helps attract birds which will feed on the caterpillars.

Spray With Btk

Control youthful bagworms by using a pesticide containing Bacillus thuringiensis var. Kurstaki (Btk), a natural soil bacterium which makes caterpillars stop feeding and die within just a few days. Once the bags are still smaller than 1/2-inch long, you must start spraying Btk in your plants and the larvae are feeding, generally from May through the end of June. Carefully read and follow the application and mixing directions on the item’s tag. 1 pesticide advocates mixing 4 tsp of product for every 1 gallon of water. With a handheld garden sprayer, thoroughly saturate all leaves surfaces, including the tops and undersides of leaves. Until you achieve control, repeat applications.

Employ Spinosad

Spinosad is a pesticide created from soilborne bacteria. It toxins caterpillars that eat or touch it killing bagworms. Follow the directions on the tag of the manufacturer since instructions will be different. 1 product advocates mixing 4 tablespoons of product for every 1 gallon of water at a handheld sprayer. Spray the tree until you cover the tops and bottom surfaces of the foliage of the host plant. In case bagworm inhabitants persist, apply spinosad solution in seven to 14 days.

A Word of Warning

Spinosad is toxic to honeybees for about three hours after application. Spray in the early morning or late evening to avoid damaging the insects. Btk – or spinosad-based products. Pesticide after a heavy rain. Even these organic ingredients can cause skin or eye irritation although spinosad and Btk offer bagworm control. Protect yourself from exposure by wearing goggles, a facemask shoes with socks, long sleeves and shorts. Maintain out family and pets of the treatment area before the spray dries.

See related

How Do I Eliminate Water Stains?

If your water comes from a well, it’s bound to include some minerals magnesium and calcium. If you use that water to take a shower, the runoff leaves white stains, which eventually become noticeable on glass doors and walls. Getting rid of these stains is not that hard.

Vinegar or Lemon Juice

The salts of calcium and calcium producing the white stains will dissolve in a weak acid, and you do not need to look far to find an effective one; equally white vinegar and lemon juice are acidic. Pour of these right into a spray bottle — no diluting is demanded — and spray it directly on the stains. The stains dissolve in about five minutes, and you can wipe them off. Be sure to rinse with water to finish.

An Abrasive Alternative

A paste made from baking soda and vinegar helps eliminate stains from corners and other hard-to-reach places. Spread the glue — since it releases carbon dioxide, which should be fizzing with a rag. Scrub with a toothbrush if necessary. This cleansing solution deodorizes as it cleans, and the residue is easily rinsed away with water.

See related

The Way to Troubleshoot a Karcher Power Washer

Karcher, the world market leader in pressure washers as of 2013, offers an lineup of over 120 products. The organization’s power washers include the small K 2.150 to the fully featured K 5.540, and although most models operate on electricity, Karcher also produces gas-powered machines. As a result of this variety, your Karcher user’s manual serves as the source for troubleshooting information. You can turn from the manufacturer to operate through issues that are fundamental.

Simple Solutions

Pressure washer failures often have remedies. If your electrical power washer will not start, hit the”Reset” button on your power outlet, if it’s one, or assess your fuse box for a tripped circuit breaker. For models with nonstarting engines, slide the lever to the closed position and then squeeze the sprayer trigger to release pressure before attempting to start the engine. In case your Karcher sprayer leaks at the nozzle connection point, tighten the hose connection or replace the rubber washer using a one of the size.

Problems With Stress

If your pressure washer gets in the pressure section check the attached garden hose for kinks or leaks and be sure the valve of the hose is turned open. If your hose is a bit small, hook your washer till a garden hose with a diameter; Karcher urges a hose. Hand-tighten the nozzle at the point until it’s airtight. Cleaning and removing the washer filter will help alleviate this matter. To clean the filter, then rinse it with warm water to remove debris and dirt.

Servicing the Sprayer

Problems with weapon and the sprayer wand contribute to decreased pressure and an erratic stream. If you experience these issues, assess the sprayer to ensure it isn’t put to the”Low” position. Inspect the tip of the sprayer nozzle by blowing to the nozzle or squeezing the obstruction out using a needle and then clear the debris. Remove the sprayer, if you notice signs of calcification on the nozzle and operate distilled vinegar through the tube along with its own wand and gun attachment. Until you feel it lock into position to the handle-like gun, twist the wand for a leaky sprayer.

Contacting Karcher

Complex problems such as leaky pumps, oil leaks and broken”O” rings require professional care from Karcher. To get an authorized Karcher fix expert, use the service center locator at the official site, which features a video and text knowledge base for power washer issues of Karcher. Karcher provides customer service . The business covers its own lineup of pressure washers under a warranty, provided you register your product upon purchase at the company’s site.

See related

Ground Cover Ideas with Dirt

A massive area of dirt leaves the landscape. Dirt can be very likely to blow or wash off, leaving behind ruts. Cheap ground-covers can conceal the dirt and also help hold it in position. The way that you choose to cover the dirt depends on the look and also its location you need for it.

Grow Low

Ground-cover plants usually grow low to the ground in clumps blossom or that spread. The plants also grow rapidly, covering dirt. One example is the showy dewflower (Drosanthemum floribundum), which is hardy in U.S. Department of Agriculture plant hardiness zones 9 through 11 and produces pink flowers. Another choice is Japanese spurge (Pachysandra terminalis). It is a perennial in USDA zones 4 through 8 and contains plenty of green leaves. The wall germander (Teucrium chamaedrys), hardy in USDA zones 5 through 9, flowers in late spring and early summer. It grows up to 1 foot tall but may be trimmed to keep it a ground cover. Avoid picking plants which are considered invasive; they harm their ecosystem and can become overgrown.

Divide and Conquer

Regardless of what kind of plant you select, you can save yourself cash by dividing. A”Horticulture” magazine website article recommends purchasing plants in late summer or early autumn when they are very likely to be priced lower than other days of the year. Divide the plants into two or three bunches so that you are able to cover more ground together, when you get them home. As they grow, they’ll fill the gaps. It requires time to cover dirt fully, however you save a lot of cash when you buy just a couple of plants and allow them to take over the distance obviously.

Break it Up

Rocks, pavers or stone over dirt split up the plants for interest. This method will be able to help you save some money on in the event that you’ve got leftover pavers, bricks or stone from a landscaping project. Utilize stone, bricks or pavers to create a pathway through the plants, if the place can also be a walkway from the landscape. River rock or inexpensive pea gravel also works to cover part of this dirt or to create a pathway. Visual contrast is created by the combination of materials in addition to being operational, in the area.

Fill in Gaps

If you do not need a solid rug of plants, mulch is a means. The mulch also works well in the beginning when you’re waiting to propagate and cover more ground. An organic mulch, such as wood chips, breaks down giving nutrients to the soil and ground-cover plants. Assess the price for a delivery of mulch since it’s often more affordable than purchasing bags of compost in a home-improvement shop, In case you’ve got a huge area to mulch.

See related

The Way to Grow Corn in an Earthbox

The EarthBox is a program intended for growing fruit, vegetables and herbs in small spaces. It is made up of a plastic box with a watering system, growing medium and an elasticized compost cover. You can purchase casters and a trellis attachment to get this. You supply plants and the soil. It’s frequently used where folks do not have garden area, such as on flat patios and balconies. At 29 inches by 14 inches, and 11 inches deep, surprisingly it has sufficient space to grow vegetables that are massive like corn to maturity.

Assemble the EarthBox according to the instructions which consists of installing the aeration screen in water and the base in 1 corner. If you have them, install the optional casters. Place the EarthBox after all danger of frost has passed. Shield the floor with plastic sheeting because water runs out of the base of this EarthBox.

Pour 2 cubic feet of container growing medium into a bucket. You may use any brand, although the EarthBox company sells packaged mix because of its platform. Add water mixing with a trowel, to create the growing medium.

Pack a small sum of the growing mixture into each of these two corners of this EarthBox not insured by the aeration screen. This water will be wicked up into the container properly. Don’t place into the water fill tube.

With growing mixture to two inches below the 12, fill out the EarthBox. Distribute 1 pound of dolomite across the surface of the ground. Insert mixture that is growing up to the rim of this EarthBox. Mix growing media’s 3 to 4 inches to disperse the dolomite evenly throughout this layer.

Dig at a trough. Pour 2 cups of artificial fertilizer or 3 cups of organic fertilizer evenly into the trough. Corn wants a whole lot of nitrogen, therefore use one whose first number is 15.

Top off the EarthBox together with the growing mixture that is remaining and mound it up about two inches. Stretch the compost cover within to cover the soil, black side up. Slip the edges that are elastic beneath the rim.

Cut an X into the compost cover with scissors about two inches from the corner. Cut four additional holes about 6 inches apart down the long side of this EarthBox. Cut five more holes on the side of this EarthBox corresponding to the position of the first row. Push on a corn seed into each hole 1 / 2 to 2 inches deep into the ground.

Pour water into the fill tube till it runs out of the overflow holes close to the base of this EarthBox. You’ll need about 3 liters of water for the first fill. Add water every day before the seedlings are about 4 to 5 inches tall. After that, water.

The ears of corn when they are full of with a white liquid along with kernels comes out when you squeeze one with your thumbnail.

See related

How to Repair Light Fixtures Loose is Hanging

When you don’t have anything solid to which you can attach a light fixture, then it’s tempting to twist it into the drywall, but that’s a code violation in addition to a mistake. The fixture may appear stable, but a consequence or the burden of the fixture itself can be enough to loosen the screws, and the outcome is a fixture dangling from the ceiling or wall. Light fittings should be attached to boxes secured into a stud or rafter, but if your fixture does not weigh much, you can use a sanding box that anchors to the drywall.

Turn off the breaker switch. If other men and women are home, let them know so that it inadvertently turns on while you’re working you’re working on the electricity and tape the switch in the off position with a notable sign.

Remove the screws that are currently holding the fixture with a screwdriver and pull it far enough away from the ceiling or wall to get the wire connections. Remove and untwist the valve wires from the circuit wires.

Install an electrical box to the fixture. The fixture does not weigh much and if the drywall is in good shape, you can put in a sanding box by cutting out a hole for it. A box includes anchors that hook into the back of the drywall, eliminating the requirement to attach it . But it ought to be held with a round ceiling box secured into a stud or rafter, which may mean altering its position, if the fixture is thick. There’s a way to stop from altering the place of a ceiling fixture if you’ve got access.

With telescoping strapping, which is designed for hanging ceiling lighting between rafters Buy a round ceiling box. Position the box above this fixture’s location and cut a hole for it in the drywall with a drywall saw. Extend the straps to meet with the ceiling rafters and then twist them into the rafters. The front edge of this box ought to be flush with the ceiling when installed.

Cut a hole to get a conventional round ceiling box without strapping next to a stud or rafter wash the box into the wood with the front edge flush with the surface of ceiling or the wall. You have to cut a part of drywall to get this done and repair it.

Hold the circuit cable, which includes a white, a black and a wire, through the back of both of the two types of boxes that you attach to framing following the box is in place. Nevertheless, feed in the cables before you anchor the box if you’re using a box. They should be stapled into a stud or rafter near the box with wire staples boxes are self-clamping — or clamped within the box.

Screw an adapter plate, called a crossbar, to the box that includes holes that line up with the screw holes on the base of this fixture. You may need to search to find an crossbar When it’s a classic fixture. You are probably going to have the ability to find one in a shop that sells lighting fixtures or electrical equipment.

Connect the fixture into the circuit cables by turning its black wire to the black one in its white you and the circuit cable to the circuit cable. By screwing on a wire cap Shield the intersection of each pair of cables.

Join the fixture ground wire to the circuit ground wire. The base is made from metal and When there is no ground wire, put in a ground screw on the base. The circuit ground wire should be on the ground screw on the box, even if it’s made from metal.

Push all the cables and then screw the fixture with screws into the adapter plate.

See related